Nortel 425-24T Configuration Manual Download Page 441

Page: 441 / 488

Default settings

441

System Configuration Guide

Image Filename

Zero-length string

“Software Download screen” on
page 237

Diagnostics Filename

Zero-length string

TFTP Server IP Address

0.0.0.0
(no IP address assigned)

Start TFTP Load of New Image

Configuration Image Filename

Zero-length string

“Configuration File Download/Upload
screen” on page 240

TFTP Server IP Address

0.0.0.0
(no IP address assigned)

Copy Configuration Image to
Server

Retrieve Configuration Image from
Server

ASCII Configuration Filename

Zero-length string

“ASCII Configuration file Download” on
page 244

TFTP Server IP Address

0.0.0.0

Retrieve Configuration File from
Server

Last Manual Configuration Status

Passed

Last Auto Configuration Status

Passed

Auto Configuration on Reset

Disabled

Table 167

Factory default settings (continued)

Field

Default setting

Appears in this CI screen

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 441 / 488

Search results

Summary of Contents for 425-24T

Reviews: