manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 208 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 208

208

Chapter 5 Using the Web-based management interface

320985-A Rev 01

 

Figure 76   

Stack Information page

Table 45

 describes the fields on the 

Stack Information 

and 

Stack Inventory

 

sections of the 

Stack Information

 page.

Table 45   

Stack Information page fields

Section

Field

Description

Stack 
Information

System Description

The name created in the configuration process to identify the 
stack.

Software Version

The version of the running software.

MAC Address

The MAC address of the stack.

IP Address

The IP address of the stack.

Manufacturing Date 
Code

The date of manufacture of the board in ASCII format: 
YYYYMMDD.

Serial Number

The serial number of the base unit.

Operational State

The current operational state of the device. The operational 
states are: Other, Not Available, Removed, Disabled, Normal, 
Reset in Progress, Testing, Warning, Non Fatal Errors, Fatal 
Error, and Not Configured

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments