manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 133 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 133

Chapter 3 CLI Basics

133

System Configuration Guide

 

Table 22

 describes the parameters and variables for the 

configure

 command.

interface command

The 

interface

 command moves you to the Interface Configuration (config-if) 

command mode. The syntax for the 

interface

 command is:

interface FastEthernet <portlist>

The 

interface

 command is in the config command mode.

Table 23

 describes the parameters and variables for the 

interface

 command.

disable command

The 

disable

 command returns you to the User EXEC (exec) command mode. 

The syntax for the 

disable

 command is:

disable

The 

disable

 command is in the privExec command mode.

The 

disable

 

command has no parameters or variables.

Table 22   

configure command parameters and variables

Parameters and 
variables

Description

terminal | network

Specifies the source for the configuration commands for the Ethernet Switch 
325/425:

terminal—allows you to enter config mode to enter configuration commands

network—allows you to set up parameters for auto-loading a script at boot-up 
or for loading and executing a script immediately

Table 23   

interface command parameters and variables

Parameters 
and variables

Description

<portlist>

Specifies the portlist you want to be affected by all the commands 
issued in the config-if command mode.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments