manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 238 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 238

238

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

To download the software image, you need a properly configured Trivial File 
Transfer Protocol (TFTP) server in your network, and an IP address for the switch 
(or stack, if configured). To learn how to configure the switch or stack IP address, 
refer to 

“IP Configuration/Setup screen” on page 214

.

To open the 

Software Download 

screen:

➨

Choose 

Software Download

 (or press

 f

) from the main menu.

You can monitor the software download process by observing the LEDs 
(see

“LED Indications during the download process” on page 240

).

Precaución: 

No interrumpa la alimentación del dispositivo durante el 

proceso de descarga del software. Si lo hace, puede alterar la imagen de 
la programación (firmware).

Attenzione: 

Non interrompere l'alimentazione elettrica al dispositivo 

durante il processo di scaricamento del software. In caso di interruzione, 
l'immagine firmware potrebbe danneggiarsi.

 

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments