manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 358 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 358

358

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

Figure 143   

Telnet window with custom banner

To disable the banner:

➨

In the 

Banner

 tab, click the 

disabled

 radio button, and then click 

Apply

.

To check that the banner is disabled: 

➨

In the Main Menu, click on 

Device > Telnet.

The 

Telnet

 window opens without the banner.

Working with configuration files

This chapter describes how you can view information and upload or download the 
configuration and image files.

FileSystem dialog box

To open the 

Edit FileSystem 

dialog box:

******************************************************************************

Ethernet Switches 325/425

******************************************************************************

Enter Ctrl-Y to begin. 

  ***************************************************************

  *** Ethernet Switch 425-24T                                 ***

  *** Nortel                                                  ***

  *** Copyright (c) 1996-2005,  All Rights Reserved           ***

  *** Release 3.6                                             ***

  *** HW:0A       FW:3.5.0.2   SW:v3.6.0                      ***

  ***************************************************************

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments