manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 64 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 64

64

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

Vorsicht: Bitte sofort lesen.

Sehen Sie nach, ob dieses Netzkabel über den richtigen Stecker verfügt und für 
die Verwendung in Ihrem Stromversogungsnetz zertifiziert ist. Falls dieses Kabel 
nicht für das Stromversorgungsnetz in Ihrem Land geeignet ist, darf es nicht 
verwendet werden. Besorgen Sie sich ein Kabel, das die Vorschriften der 
Zulassungsbehörden in Ihrem Land erfüllt.

Die technische Dokumentation dieses Produkts enthält ausführliche 
Installationsanweisungen, die nur von qualifiziertem Kundendienstpersonal 
ausgeführt werden dürfen.

Attention: Lisez ceci immédiatement. 

Examinez ce cordon d'alimentation pour déterminer s'il dispose de la fiche 
appropriée et s'il est bien agréé pour utilisation sur votre installation 
électrique. Débarrassez-vous en immédiatement s'il ne convient pas à 
l'utilisation sur le secteur électrique en usage dans votre pays et 
procurez-vous un cordon conforme à la réglementation nationale en vigueur.

Reportez-vous à la documentation technique de ce produit pour obtenir des 
instructions détaillées d'installation, destinées à un technicien qualifié.

Attenzione: Leggere attentamente. 

Controllare questo cavo di alimentazione, verificarne il collegamento con la 
presa appropriata nonché la certificazione per l'uso nell'impianto elettrico 
posseduto. Non utilizzare assolutamente in caso tale cavo non sia adatto al 
sistema elettrico del paese in cui viene utilizzato e richiederne un altro 
certificato dall'ente nazionale di fornitura elettrica.

Per le procedure di installazione che devono essere seguite dal personale di 
servizio, consultare questa documentazione tecnica del prodotto.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments