manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 455 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 455

Command List

455

System Configuration Guide

 

no logging remote address

System Monitoring Guide for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

no logging remote enable

System Monitoring Guide for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

no logging remote level

System Monitoring Guide for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

no mac-security

Configuring and Managing Security for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)

no mac-security mac-address-table {address 
<H.H.H>|port <portlist>|security-list <1-32>]

Configuring and Managing Security for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)

no mac-security mac-da-filter {add|delete}<H.H.H.>

Configuring and Managing Security for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)

no mac-security security-list <1-32>

Configuring and Managing Security for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)

no mlt [<id>]

Configuring VLANs, Spanning Tree, and 
MultiLink Trunking for Nortel Ethernet Switches 
325 and 425, Software Release 3.6

(320986-A)

no name [port <portlist>]

page 322

no port-mirroring

System Monitoring Guide for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

no radius-server

Configuring and Managing Security for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)

no rate-limit [port <portlist>]

page 330

no rmon alarm [<1-65535>]

System Monitoring Guide for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

no rmon event

System Monitoring Guide for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

Table 168   

CLI command list (continued)

Command

Page No.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments