manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 68 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 68

68

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

Table 6   

Components of the Ethernet Switch 425-24T front panel

User Interface button

The User Interface (UI) button on the Ethernet Switch 425 provides easy-to-use 
features for stacking configuration.

You can perform the following tasks using the User Interface button on the 
Ethernet Switch 425-24T: 

•

“Setting the unit as the Base Unit” on page 69

•

“Setting the unit as the non-base unit” on page 69

•

“Setting the unit as a standalone unit” on page 70

•

“Resetting the stack” on page 70

•

“Resetting the unit” on page 70

•

“Setting the default IP address” on page 72

 

Item

Description

1

UI button

2

10/100/1000BaseT (copper) port 25 and 26

3

Gigabit Interface Converter (GBIC) ports 25 and 26

4

10/100BaseT ports 1 to 24

5

Console port

Note: 

With Release 3.6 software, the Ethernet Switches 425-24T and 

425-48T have stacking enabled by default, which means that ports 26 
and 50, respectively, are disabled by default. This is because the cascade 
port shares resources with port 26 on the Ethernet Switch 425-24T and 
port 50 on the Ethernet Switch 425-48T. Either the cascade port can be 
active, or port 26 or 50 can be active. 
If you want to use port 26 or port 50 in standalone mode, disable 
stacking and reboot the switch.

Note: 

On the Ethernet Switch 425-24T and 425-48T, the User Interface 

button allows you to reset the unit.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments