Nortel 425-24T Configuration Manual Download Page 313

Page: 313 / 488

Chapter 7 System configuration using the CLI

313

System Configuration Guide

Table 104

describes the parameters for the

blink-leds

command.

Configuring UI button

ui-button enable command

The

ui-button enable

command enables the UI button.

The syntax for the

ui-button enable

command is:

ui-button enable

The

ui-button enable

command is in the privExec mode.

The

ui-button enable

command has no parameters or variables.

Figure 121

displays a sample output of the

ui-button enable

command.

Figure 121

ui-button enable command output

Table 104

blink-leds command parameters and variables

Parameters and Variables

Description

off

Sets the LEDs to stop blinking.

time

Indicates the duration for the LEDs to blink in
order to identify the unit.

unit

Specifies the unit number to which the command
is applied.

425-48T(config)#ui-button enable

425-48T(config)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 313 / 488

Search results

Summary of Contents for 425-24T

Reviews: