manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 137 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 137

Chapter 3 CLI Basics

137

System Configuration Guide

 

Warning the switch/stack has been set to reload in <xx> 

minutes. Current configuration has NOT been saved. 

Configuration must be explicitly saved.

Once the reload timer expires, the switch resets, reloads the last 

saved

 

configuration, and re-enables the autosave feature. 

The syntax for the 

reload

 command is:

reload [force] [minutes-to-wait <1-60>] [cancel]

Table 23

 describes the parameters and variables for the 

interface

 command.

The 

reload

 command is in the privExec command mode.

Managing basic system information

This section shows you how to view basic system information, such as the current 
software version and the stack mode; you can renumber the units within a stack. 
The following topics are covered:

•

“show sys-info command”

•

“show tech command” on page 139

•

“show stack-info command” on page 141

•

“show stacking-mode command” on page 142

•

“renumber unit command” on page 143

Table 25   

reload command parameters and variables

Parameters 
and variables

Description

force

Instructs the switch to skip the reload confirmation prompt.

minutes-to-wait 
<1-60>]

Specifies the number of minutes that pass before the switch reloads 
itself. The default wait time is set at 10 minutes.

cancel

Aborts all scheduled switch reloads

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments