Nortel 425-24T Configuration Manual Download Page 288

Page: 288 / 488

288

Chapter 7 System configuration using the CLI

320985-A Rev 01

Figure 107

show autosave command output

autosave enable command

The

autosave enable

command enables the autosave feature. The syntax for

the

autosave enable

command is:

autosave enable

The

autosave enable

command is in the config command mode.

The

autosave enable

command has no parameters or variables.

no autosave enable command

The

autosave enable

command disables the autosave feature. The syntax

for the

no autosave

enable

command is:

no autosave enable

The

no autosave enable

command is in the config command mode.

The

no autosave enable

command has no parameters or variables.

default autosave enable command

The

default

autosave enable

command defaults the autosave feature to the

default value of enabled. The syntax for the

default autosave enable

command is:

default autosave enable

The

default autosave enable

command is in the config command mode.

The

default autosave enable

command has no parameters or variables.

425-48T(config-if)#show autosave

Auto Save: Enabled

425-48T(config-if)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 288 / 488

Search results

Summary of Contents for 425-24T

Reviews: