Nortel 425-24T Configuration Manual Download Page 393

Page: 393 / 488

Chapter 12 Configuring the switch using Web-based management

393

System Configuration Guide

Configuring high speed flow control

You can view the High Speed Flow Control parameters for Ethernet Switch 325/
425 in this page.

To configure high speed flow control:

From the main menu, choose

Configuration > High Speed Flow Control

The

High Speed Flow Control

page opens

(Figure 161)

Figure 161

High Speed Flow Control page

Table 147

describes the items on the

High Speed Flow Control

page.

Table 147

High Speed Flow Control page items

Item

Range

Description

Port

The switch port number of the corresponding row.

Autonegotiation

(1) Enabled

(2) Disabled

Displays if the autonegotiation feature is enabled or disabled.

When enabled, the port advertises support only for 1000Mb/s
operation in full-duplex mode.

Flow Control

(1) Enabled

(2) Symmetric

(3) Asymmetric

Displays current settings of flow control.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 393 / 488

Search results

Summary of Contents for 425-24T

Reviews: