manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 109 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 109

Chapter 2 Using the console interface

109

System Configuration Guide

 

Port Configuration screen

The 

Port Configuration

 screen (Figures 

22

 and 

23

) allows you to configure 

specific switch ports or all switch ports. You can enable or disable the port status 
of specified switch ports, set the switch ports to autonegotiate for the highest 
available speed of the connected station, or set the speed for selected switch ports 
(autonegotiation is not supported on fiber optic ports).

You can disable switch ports that are trunk members (except the lowest member 
of an active trunk which cannot be disabled until it is removed from the MLT); 
however, the screen prompts for verification of the request before completing the 
action. Choosing 

Yes

 disables the port and removes it from the trunk.

To open the 

Port Configuration

 screen:

➨

Choose 

Port Configuration

 (or press 

p

) from the 

Switch Configuration 

Menu 

screen.

Note: 

You cannot disable a port that is a member of the MLT if the 

switch is operating in the RSTP/MSTP mode.

Note: 

The 

Autonegotiation

 fields, the 

Speed

 fields, and the 

Duplex

 

fields are independent of MultiLink Trunking, VLANs, and the STP.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments