Nortel 425-24T Configuration Manual Download Page 459

Page: 459 / 488

Command List

459

System Configuration Guide

save config

page 286

show arp-table

page 282

show auto-negotiation-advertisements [port
<portlist>]

page 331

show auto-negotiation-capabilities [port <portlist>]

page 332

show autosave

page 287

show autotopology nmm-table

page 299

show autotopology settings

page 298

show banner [ custom | static ]

page 281

show config-network

page 267

show cli [info|mode|password]

page 272

show clock summer-time

page 296

show clock time-zone

page 296

show eapol

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

show eapol guest-vlan

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

show http-port

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

show interfaces [names] [<portlist>]

page 283

show interfaces [<portlist>] config

page 284

show ip address [address [stack|switch]]

page 256

show ip [bootp] [default-gateway] [address
[stack|switch]]

page 255

show ip dns

page 262

show ipmgr

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

show lacp debug member [portlist]

Configuring VLANs, Spanning Tree, and
MultiLink Trunking for Nortel Ethernet Switches
325 and 425, Software Release 3.6

(320986-A)

Table 168

CLI command list (continued)

Command

Page No.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 459 / 488

Search results

Summary of Contents for 425-24T

Reviews: