manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 63 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 63

Chapter 1 About Ethernet Switches 325 and 425

63

System Configuration Guide

 

United Kingdom:

•

BS1363 male plug with 
fuse

•

Harmonized cord 

240 VAC 
50 Hz 
Single phase

Australia:

AS3112-1981 Male plug

240 VAC 
50 Hz 
Single phase

Caution: 

 

Please read immediately.

Inspect the power cord and determine if it provides the proper plug and is 
appropriately certified for use with your electrical system. Immediately 
discard this power cord if it is inappropriate for your country's electrical 
system and obtain the proper cord as required by your national electrical 
codes or ordinances.

Refer to this product's technical documentation for detailed installation 
procedures to be followed by qualified service personnel.

Table 5   

International power cord specifications (continued)

Country/Plug description

Specifications

Typical plug

229FA

230FA

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments