Nortel 425-24T Configuration Manual Download Page 213

Page: 213 / 488

213

System Configuration Guide

Chapter 6
System configuration using the Console Interface

This chapter describes how to configure and manage the Ethernet Switch 325/425
using the menu-driven Console Interface (CI).

This chapter covers the following topics:

•

“IP Configuration/Setup screen”

•

“SNMP Configuration screen”

•

“System Characteristics screen” on page 221

•

“Console/Comm Port Configuration screen” on page 223

•

“Logging in” on page 231

•

“Renumber Stack Units screen” on page 232

•

“Hardware Unit Information screen” on page 233

•

“TELNET/SNMP/Web Access Configuration screen” on page 234

•

“Software Download screen” on page 237

•

“Configuration File Download/Upload screen” on page 240

•

“ASCII Configuration file Download” on page 244

•

“Using SNTP”

•

“Using DNS to ping and Telnet”

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 213 / 488

Search results

Summary of Contents for 425-24T

Reviews: