manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 247 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 247

Chapter 6 System configuration using the Console Interface

247

System Configuration Guide

 

Enabling and disabling autosave

The 

Autosave Configuration 

screen (

Figure 91

) allows you to enable and disable 

the autosave feature on the switch or stack.

To view the 

Autosave Configuration

 screen:

➨

From the 

Configuration File Menu

, choose 

Autosave Configuration

 (or 

press

s

).

Figure 91   

Autosave Configuration screen

Table 57

 describes the fields available in the 

Autosave Configuration

 screen.

Table 57   

Autosave Configuration screen fields

Field

Description

Autosave

Enables or disables the autosave feature.

                            Autosave Configuration

      Autosave       [  Enabled   ]

Use space bar to display choices, press <Return> or <Enter> to select choice.

Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments