manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 281 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 281

Chapter 7 System configuration using the CLI

281

System Configuration Guide

 

The 

banner

 command for displaying banner is in the config mode.

Table 81

 describes the parameters for the banner command.

show banner command

The 

show banner

 command displays the banner. The syntax for the 

show 

banner

 command is: 

show banner [ custom | static ]

The 

show banner

 command is in the config mode.

Table 82

 describes the parameters for the banner command.

no banner command

The 

no banner 

command allows you to clear all lines of a previously stored 

custom banner. The syntax for the 

no banner 

command is:

no banner

Table 81   

banner command parameters

Parameters

Description

static

Displays the default agent-banner.

custom

Displays the custom agent-banner.

disabled

Skips the agent-banner display.

<1-15> 

LINE

Fills the Nth line of the custom banner 

(1<N<15) 

with the 

text specified in 

LINE.

Table 82   

show banner command parameters

Parameters

Description

static

Displays default banner

custom

Displays custom banner

(if empty)

Displays static, custom or disabled status if 
parameter is not entered. 

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments