manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 298 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 298

298

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

no autotopology command

The 

no

 

autotopology

 command disables the Autotopology protocol. The 

syntax for the 

no

 

autotopology

 command is:

no autotopology

The 

no

 

autotopology

 command is in the config command mode.

The 

no

 

autotopology

 command has no parameters or values.

default autotopology command

The 

default

 

autotopology

 command enables the Autotopology protocol. The 

syntax for the 

default

 

autotopology

 command is:

default autotopology

The 

default

 

autotopology

 command is in the config command mode.

The 

default

 

autotopology

 command has no parameters or values.

show autotopology settings

The

 show autotopology settings 

command displays information on the 

Autotopology configuration. The syntax for the

 

show autotopology settings 

command is:

show autotopology settings

The

 show autotopology settings 

command is in the privExec mode.

The 

show autotopology settings

 command has no parameters or variables. 

Figure 111

 displays a sample output of the

 show autotopology settings 

command.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments