manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 262 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 262

262

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

•

“ip domain-name command” on page 265

•

“no ip domain-name command” on page 265

•

“default ip domain-name command” on page 265

show ip dns command

The 

show ip dns

 command displays the DNS domain name, as well as any 

configured DNS servers. The syntax for the 

show ip dns 

command is:

show ip dns

The 

show ip dns 

command is in the exec command mode.

The 

show ip dns 

command has no parameters or variables. 

Figure 95

 displays sample output from the 

show ip dns 

command.

Figure 95   

show ip dns

 command output

ping command

The 

ping

 command tests the network connection to another network device. The 

command sends an Internet Control Message Protocol (ICMP) packet from the 
switch to the target device. The local IP address must be set before issuing the 

ping

 command. 

You can ping a host using either its IP address or hostname.

425-48T(config)#show ip dns

DNS Default Domain name: None

DNS Servers

-----------

0.0.0.0

0.0.0.0

0.0.0.0

425-48T(config)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments