manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 210 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 210

210

Chapter 5 Using the Web-based management interface

320985-A Rev 01

 

Figure 77   

Stack Numbering Setting page

Table 46

 describes the fields on the Stack Numbering Setting page.

2

Click 

Submit

.

A message opens prompting you to confirm your request.

3

Do one of the following:

•

Click 

OK

 to renumber the stack.

•

Click 

Cancel

 to return to the 

Stack Numbering

 page without making 

changes.

Table 46   

Stack Numbering Setting page fields

 Item

Range

Description

Current Unit Number 1..8

Unit number previously assigned to the policy switch. The 
entries in this column are displayed in the order of their current 
physical cabling with respect to the base unit, and can show 
nonconsecutive unit numbering if one or more units were 
previously moved or modified. The entries can also include 
unit numbers of units that are no longer participating in the 
stack (not currently active).

MAC Address

XX.XX.XX.XX.XX.XX MAC address of the corresponding unit listed in the Current 

Unit Number field.

New Unit Number

1..8

Choose a new number from the list to assign to your selected 
policy switch. 

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments