manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 70 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 70

70

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

The color and status of the UI LED returns to steady green once the command 
has been accepted. If the command is rejected, the UI LED turns amber 
blinking.

Setting the unit as a standalone unit

To set the unit as a standalone unit using the UI button:

1

Press and hold the UI button until the UI LED displays the Green/blinking 
status.

2

Press the UI button 6 times.

3

Press the UI button and hold it for 3 seconds to confirm the command.

Resetting the stack

To reset the stack using the UI button:

1

Press the UI button and hold in for three seconds.

The unit is now in configuration mode, and the color and status of the UI LED 
turns green blinking.

2

Press the UI button three times.

The color and status of the Base, Down, and Up LEDs turn amber blinking.

3

Press the UI button and hold it for three seconds to confirm the command.

Resetting the unit

To reset the unit at any time, with the UI button, do the following:

1

Press the UI button for 3 seconds. The switch operates in the Configuration 
mode. The UI LED turns green and will blink.

2

Press UI button 3 times.

Note: 

Changing the Base Unit does not take effect until you restart the 

system.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments