manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 324 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 324

324

Chapter 8 Ethernet port management using the CLI

320985-A Rev 01

 

Table 111

 describes the parameters and variables for the 

speed

 

command. 

default speed command

The 

default

 

speed

 command sets the speed of the port to the factory default 

speed. The syntax for the 

default

 

speed

 command is:

default speed [port 

<

portlist>]

The 

default

 

speed

 command is in the config-if command mode.

Table 111   

speed command parameters and variables

Parameters and 
variables

Description

port <portlist>

Specifies the port numbers to configure the speed. Enter the port 
numbers you want to configure.

Note:

 If you omit this parameter, the system uses the port number 

you specified in the 

interface

 command.

10|100|1000|auto

Sets speed to:

•

10—10 Mb/s

•

100—100 Mb/s

•

1000—1000 Mb/s or 1 GB/s

•

auto—autonegotiation 

Note: 

When you set the port speed for autonegotiation, ensure that the 

other side of the link is also set for autonegotiation.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments