Nortel 425-24T Configuration Manual Download Page 401

Page: 401 / 488

Chapter 12 Configuring the switch using Web-based management

401

System Configuration Guide

Figure 165

Console/Communication Port page

Table 153

describes the items on the

Console/Communication Port

page.

Select from the list.

Click

Submit

Table 153

Console/Communication Port page items

Item

Range

Description

Comm Port Data Bits

The current console communication port data bit
setting.

Comm Port Parity

The current console communication port parity setting.

Comm Port Stop Bits

The current console communication port stop bit
setting.

Console Port Speed

2400
4800
9600
19200
38400

Choose the console port speed baud rate.

Note:

The default setting is 9600.

Caution:

If you choose a baud rate that does not

match your console terminal baud rate, you will lose
communication with the configuration interface when
you click Submit.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 401 / 488

Search results

Summary of Contents for 425-24T

Reviews: