manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 54 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 54

54

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

Flash memory storage

Switch software image storage

The Ethernet Switch 325/425 uses flash memory to store the switch software 
image. The flash memory allows you to update the software image with a newer 
version without changing the switch hardware (see 

“Software Download screen” 

on page 237

). An in-band connection between the switch and the TFTP load host 

is required to download the software image.

Autosensing, and autonegotiation

The Ethernet Switch 325/425 is an autosensing and autonegotiating device:

•

The term autosense refers to the ability of a port to sense the speed of an 
attached device.

•

The term autonegotiation refers to a standardized protocol (IEEE 802.3u) that 
exists between two IEEE 802.3u-capable devices. Autonegotiation allows the 
switch to select the best of speed and duplex modes.

Autosensing is used when the attached device is not capable of autonegotiation or 
is using a form of autonegotiation that is not compatible with the IEEE 802.3u 
standard. In this case, since it is not possible to sense the duplex mode of the 
attached device, the Ethernet Switch 325/425 reverts to half-duplex mode.

When autonegotiation-capable devices are attached to the Ethernet Switch 325/
425, the ports negotiate down from 100 Mb/s speed and full-duplex mode until the 
attached device acknowledges a supported speed and duplex mode.

For more information about autosensing and autonegotiation modes, see 

Chapter 13, “Troubleshooting,” on page 405

.

RFCs

For more information about networking concepts, protocols, and topologies, 
consult the following RFCs:

•

RFC 1213 (MIB-II)

•

RFC 1493 (Bridge MIB)

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments