manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 328 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 328

328

Chapter 8 Ethernet port management using the CLI

320985-A Rev 01

 

Table 116

 describes the parameters and variables for the 

no

 

flowcontrol

 

command. 

default flowcontrol command

The 

default

 

flowcontrol

 command is used only on Gigabit Ethernet ports 

and sets the flow control to auto, which automatically detects the flow control. 
The syntax for the 

default

 

flowcontrol

 command is:

default flowcontrol [port <portlist>]

The 

default

 

flowcontrol

 command is in the config-if mode.

Table 117

 describes the parameters and variables for the 

default

 

flowcontrol

 

command. 

Table 116   

no flowcontrol command parameters and variables

Parameters and 
variables

Description

port <portlist>

Specifies the port numbers to disable flow control.

Note:

 If you omit this parameter, the system uses the port 

number you specified in the 

interface

 command.

Table 117   

default flowcontrol command parameters and variables

Parameters and 
variables

Description

port <portlist>

Specifies the port numbers to default to auto flow control.

Note:

 If you omit this parameter, the system uses the port 

number you specified in the 

interface

 command.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments