manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 117 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 117

Chapter 2 Using the console interface

117

System Configuration Guide

 

Figure 25   

Rate Limiting Configuration screen

Table 19

 describes the fields in the

 Rate Limiting Configuration

 screen. 

Table 19   

Rate Limiting Configuration screen fields

Field

Description

Unit

Allows you to select the unit number (when stacking is configured) to view or 
configure. To view or configure another unit, type its unit number and press 

Enter

, or press the spacebar to toggle the unit numbers. This field is not present 

in a standalone configuration. 

Stack

Displays information relevant to the stack, if the switch is operating in the stack 
configuration.

Packet Type

Allows you to select the packet types for rate-limiting.

Default value:

Both

Range:

Both, Multicast, Broadcast

 Rate Limiting Configuration

          Packet Type     Limit

  ----   -------------   --------

Switch  [  Both       ] [ 0 pps ]

Stack   [  Both       ] [ 0 pps ]

Use space bar to display choices, press <Return> or <Enter> to select choice.

Press Ctrl-R to return to previous menu.  Press Ctrl-C to return to Main 

Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments