Nortel 425-24T Configuration Manual Download Page 414

Page: 414 / 488

414

Installing an SFP Transceiver

320985-A Rev 01

Installing SFPs

To install an SFP:

Remove the SFP from its protective packaging.

Verify that the SFP is the correct model for your network configuration. See

Table 156 on page 412

for information on the SFPs models supported.

Grasp the SFP between your thumb and forefinger.

Insert the SFP into the SFP slot on the module.

See

Figure 169 on page 415

. Apply light pressure to the SFP until the device

clicks and locks into position in the module.

1590nm/Red

•

AA1419031

•

AA1419039

•

40 KM

•

70 KM

1610nm/Brown

•

AA1419032

•

AA1419040

•

40 KM

•

70 KM

Note:

The cable distance may vary depending on the quality of fiber

optic cable used.

Caution:

SFPs are keyed to prevent incorrect insertion. If an SFP resists

pressure, do not force it; turn it over, and reinsert it.

Table 157

Nortel CWDM SFP transceiver list (continued)

CWDM SFP

Product number

Cable length

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 414 / 488

Search results

Summary of Contents for 425-24T

Reviews: