manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 57 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 57

Chapter 1 About Ethernet Switches 325 and 425

57

System Configuration Guide

 

Hardware components of the Ethernet Switch 325

Front panel

Figure 2

 shows the front and side views of the Ethernet Switch 325.

Figure 2   

Ethernet Switch 325-24G

Figure 3

 shows the configuration of the front panel on the Ethernet Switch 325. 

Table 2

 describes the components on the front panel.

Figure 3   

Ethernet Switch 325-24G front panel

UI

UI Set

25

26

Spd: 10/100/1000T

Act: Activity

LED Status - Amber:10Mps Green:100 Mps Blink:Activity

UI Cmd

Pwr

Console

Spd Act

Spd Act

1

2

3

4

5

6

7

8

9

10

11

12

LED Status - Off:Half Duplex Green:Full Duplex

13

14

15

16

17

18

19

20

21

22

23

24

Ethernet Switch 325-24G

3

1

4

2

11108ER

Ethernet Switch 325-24G

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments