Lantronix x6010 User Manual Download Page 23

Page: 23 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 23 of 261

S6010-10xx

S6010-1040

Figure 10: S6010 Front Panels

LED Descriptions

The x6010 LEDs are described below.

PWR

Power (Green) on (lit) indicates x6010 power is on.

SDF

Signal Detect on Fiber:

•

Green, on indicates fiber link is up.

•

Green, blinking indicates fiber link is in loopback mode.

•

Yellow, on indicates AIS detected on fiber link.

The

SDF

LED when lit indicates fiber link is up. Flashing

SDF

LED (once/second) indicates transmitting on

link if other link is down. Flashing

SDF

LED (5 times/second) indicates ‘All Ones’ detected on the fiber

link.

SDC

Signal Detect on Copper:

•

Green, on (lit) indicates copper link is up.

•

Green, blinking indicates copper link is in loopback mode.

•

Yellow, on (lit) indicates AIS detected on copper link.

The

SDC

LED, when lit indicates twisted-pair copper link is up. Flashing SDC LED (once/second) indicates

transmitting on link if other link is down. Flashing SDC LED (5 times/second) indicates All Ones detected

on the Link.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands