Lantronix x6010 User Manual Download Page 196

Page: 196 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 196 of 261

Message

Clear Recent History

Meaning

: You tried to display the Power Supply’s temperature, fan, voltage or power sensor sub-menu

in the Mozilla Firefox browser.

Recovery

Click

Cancel

/ Click

Clear Now

to clear the error dialog.

Make sure the latest firmware is running. See “

Upgrade the IONMM and/or NID Firmware

” on

page

Upgrade the firmware version if needed.

Expand and contract the ION Stack.

Retry the operation.

If the problem persists, contact Technical Support.

Message

Local Area Connection x – A network cable is unplugged

Meaning

: You unplugged the USB cable at the NID or IONMM, or the NID or IONMM was unplugged

from the ION chassis, or you pressed the

RESET

button on the IONMM.

Recovery

If you pressed the

RESET

button on the IONMM, wait a few moments for the message to clear.

Plug the USB cable back into the IONMM’s

USB-DEVICE

connector, or plug the USB cable back into

the NID’s

USB

connector.

Try the operation again.

If the problem persists, contact Technical Support.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands