Lantronix x6010 User Manual Download Page 56

Page: 56 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 56 of 261

Power Off a Slot

At the

Chassis

MAIN

tab, you can click the

Off

button to remove power to a specific slot in the chassis.

The message “

Are you sure to power off this slot?

” displays.

If you are not sure that you want to power off this slot, click the

Cancel

button to clear the message and

return to normal operations without resetting power to this slot.
After power off, it will take a while for the card to disappear from this slot. Fold and then unfold the

Chassis node in the left tree panel to check the progress. If the card information changes on the Tree,

then click the

Refresh

button on this page.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands