Lantronix x6010 User Manual Download Page 169

Page: 169 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 169 of 261

Cannot show slot info on this card!

You entered a “

show slot info

” command on an ION card other than an IONMM card.

Enter another (supported) show command on this card or use the “

” command to switch to the

IONMM.

Retry the operation.

If the problem persists, contact Technical Support.

ERROR Software version of this card (“cardVersion”) is not supported, please upgrade to the same

version as the IONMM

Getting card version failed

The failure get template config handler was called.

You attempted a function that is not supported by this version of firmware.
1.

Enter another (supported) function at this card’s firmware version or use the “

” command to

switch to another card.

Upgrade to a newer firmware version. See “

TFTP Transfer / Upgrade Commands

” or “

Upgrade /

Update Firmware Commands

”.

Retry the operation.

If the problem persists, contact Technical Support.

Error: this command is not supported on this port!

Error: this command should be executed on a device!

Get AIS Transmit no such object.

Get Channel Alarm Indication Signal no such object.

Get link status no such object.

You entered a command at the wrong level (device or port level), or a command that is not supported

by this device or port. For example:

AgentIII C1|S3|L1P1>

show tdm config

Error: this command should be executed on a device!

AgentIII C1|S3|L1P1>

go l1d

AgentIII C1|S3|L1D>

show tdm config

Get AIS Transmit no such object.

AgentIII C1|S3|L1D>

go l1p=1

AgentIII C1|S3|L1P1>

show tdm port config

Get Channel Alarm Indication Signal no such object.

AgentIII C1|S3|L1P1>

go l1p=3

AgentIII C1|S3|L1P3>

show tdm port config

Get link status no such object.

AgentIII C1|S3|L1P5>

go l1p=6

AgentIII C1|S3|L1P6>

show tdm port config

Error: this command is not supported on this port!

AgentIII C1|S3|L1P6>

Make sure this is the command / function that you want.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands