Lantronix x6010 User Manual Download Page 204

Page: 204 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 204 of 261

Parameter

Possible

Values

Description

Interface Characteristics

DMI ID

Unknown,

SFP/SFP+/SFP28,

GBIC, SFP,

Reserved, vendor-

specific

Specifies the physical device from SFF-8472 Rev 9.5 Standard:

00h Unknown or unspecified

01h GBIC

02h Module/connector soldered to motherboard

03h SFP

04-7Fh Reserved

80-FFh Vendor specific

Connector

Type

LC, MT-RJ LC, SC,

ST, RJ-45, or VF-

45, or unknown

The external optical or electrical cable connector provided as

the interface.

* MT-RJ: Media Termination – Recommended Jack for Duplex

multimode connections.

* LC: Lucent Connector or Local Connector for High-density

connections, SFP transceivers.

* SC: Subscriber Connector for Datacomm and Telecomm.

* ST: BFOC Straight Tip / Bayonet Fiber Optic Connector for

Multimode – rarely Singlemode (APC not possible).

* VF-45: Snap connector for Datacom uses.

See “

Connector Types

” section below.

Nominal Bit

Rate Mbps)

(measured rate)

Bitrate in units of 100Mbps (the sample screen above shows

1300, or 1.3 Gbps).

Fiber Interface

Wavelength

(nM)

(measured wave-

length)

The Nominal transmitter output wavelength at room tempera-

ture. The unit of measure is nanometers (the sample screen

above shows 850 nm).

Diagnostic Monitoring

Receive Power

(uW)

(measured power

measurement)

Receive power on local fiber measured in microwatts (the sam-

ple screen above shows

203

uW).

Receive Power

(dBM)

(measured signal

strength)

Receive power on local fiber measured in dBM (decibels rela-

tive to one milliwatt) which defines signal strength. The sample

screen above shows -

6.925

dBM.

Receive Power

Alarm

Normal -1,

Not Supported – 2,

Low Warn – 3,

High Warn – 4,

Low Alarm – 6

High Alarm – 7

Alarm status for receive power on local fiber.

Rx Power In-

trusion Thresh-

old (uW)

0 –

65535 μW

A configurable level for Rx Power on the Fiber port. If the DMI

read value falls below the preset value, an intrusion is detected,

and a trap is generated. The valid range is 0 –

65535 μW

. The

default is 0. Displays the message “

ALARM: Receive power is

below specified threshold. Fiber trap intrusion may be in pro-

gress.

” If the value falls below the specified threshold.

Temperature

(˚C)

(measured temp.)

Temperature of fiber transceiver in tenths of degrees C (Cel-

sius). The sample screen above shows 38.0

˚C.

Temperature

(˚F)

(measured temp.)

Temperature of fiber transceiver in tenths of degrees F (Fahren-

heit). The sample screen above shows 101.8

˚F.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands