manualshive.com logo in svg

Lantronix x6010, User Manual, Page: 24 / 261

Share
Download
Lantronix x6010 User Manual Download Page 24

Lantronix   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ION x6010 User Guide 

33493 Rev. F

 

https://www.lantronix.com/

  

Page 24 of 261

 

Jumper Settings

 

The x6010 jumper settings are described below.  

Jumper J8 – Configuration mode (HW / SW Mode)

: Jumper J8 defines the x6010 PCB’s Hardware / 

Software mode setting. 

•

 

1-2: Hardware mode; the x6010 configuration is controlled by 

hardware. Use the shorting plug to jumper (short) pins 1 

and 2 for Hardware Mode. 

•

 

2-3: Software mode; the x6010 configuration is controlled by 

software (default). Use the shorting plug to jumper 

(short) pins 2 and 3 for Software Mode. 

The factory default setting is Software mode (pins 2 and 3 jumpered) as shown above.

 

Note that in 

Hardware mode you cannot make x6010 configuration changes from the Web interface, as the screen 

fields are all grayed out. You can enter CLI commands with the x6010 in Hardware mode. 

 

For more information, see “

DIP Switches and Jumper Setting

s

”

. 

DIP Switches

 

Several multi-position DIP switches allow the network administrator to configure the x6010 for network 

conditions. Use a small flat blade screwdriver or similar device to set these switches for site installation. 

 
The x6010 DIP switches and jumpers are summarized below. The x6010 DIP switch settings are de-

scribed below. For more information, see “

DIP Switches and Jumper Setting

s

”

.  

DIP Switch Locations 

The S6010 DIP switch locations are shown below. 

 

 

 

Figure 11: S6010 DIP Switches 

Summary of Contents for x6010






































































































































































































































































Reviews:

No comments