Lantronix x6010 User Manual Download Page 184

Page: 184 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 184 of 261

Website displays incorrectly in Internet Explorer 8 or 9

Websites that were designed for earlier versions of Internet Explorer might not display correctly in the

current version. However, you can often improve how a website will look in Internet Explorer by using

the new ‘Compatibility View’ feature. When you turn on Compatibility View, the webpage displayed

(and any other webpages within the website’s domain) will display as if you were using an earlier ver-

sion of Internet Explorer.

1. In IE8, click the

Stop

button on the right side of the Address bar.

2. If the page has stopped loading, click the

Refresh

button to try again.

3. Click the

Tools

button, and then click

Compatibility View

If Internet Explorer recognizes a webpage that is not compatible, the

Compatibility View

button displays

on the Address bar. To turn Compatibility View on, click the

Compatibility View

button. From now on,

whenever you visit this website, it will be displayed in Compatibility View. However, if the website re-

ceives updates to display correctly in the current version of Internet Explorer, Compatibility View will

automatically turn off. Note that not all website display problems are caused by browser incompatibility.

Interrupted Internet connections, heavy traffic, or website bugs can also affect how a webpage is dis-

played. To go back to browsing with Internet Explorer 8 on that site, click the

Compatibility View

button

again.

4. Check your ION firmware version and upgrade to the latest if outdated. See the “Upgrade” section.

5. Check the Microsoft Support Online websit

http://support.microsoft.com/ph/807/en-us/#tab0

for

information.

http://support.microsoft.com/kb/960321

http://blogs.msdn.com/b/ie/archive/2008/08/27/introducing-compatibility-view.aspx

In IE9, click the

Compatibility View

toolbar button on the Address bar to display the website as

if you were using an earlier version of Internet Explorer. See the Microsoft Support website Arti-

cle ID: 956197

http://support.microsoft.com/kb/956197

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands