Lantronix x6010 User Manual Download Page 187

Page: 187 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 187 of 261

Config.err Messages

Sample config.err file information is provided below.

1-2-2-C3220-1040_20100608.config.err

Line

1 AGENT PM ERROR- CLI command remove vlan all failed

2 AGENT PM ERROR- CLI command remove fwddb all failed

3 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-10 conn-port=1 priority=1 type=staticNRL failed

4 AGENT PM ERROR- CLI command remove vlan all failed

5 AGENT PM ERROR- CLI command remove fwddb all failed

6 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-02 conn-port=1 priority=1 type=staticNRL failed

7 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-03 conn-port=1 priority=1 type=staticNRL failed

8 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-04 conn-port=1 priority=1 type=staticNRL failed

9 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-05 conn-port=1 priority=1 type=staticNRL failed

10 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-06 conn-port=1 priority=1 type=staticNRL failed

11 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-07 conn-port=1 priority=1 type=staticNRL failed

12 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-08 conn-port=1 priority=1 type=staticNRL failed

13 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-09 conn-port=1 priority=1 type=staticNRL failed

14 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-10 conn-port=1 priority=1 type=staticNRL failed

15 AGENT PM ERROR- CLI command remove vlan all failed

16 AGENT PM ERROR- CLI command remove fwddb all failed

17 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-02 conn-port=1 priority=1 type=staticNRL failed

18 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-03 conn-port=1 priority=1 type=staticNRL failed

19 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-04 conn-port=1 priority=1 type=staticNRL failed

20 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-05 conn-port=1 priority=1 type=staticNRL failed

21 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-06 conn-port=1 priority=1 type=staticNRL failed

22 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-07 conn-port=1 priority=1 type=staticNRL failed

23 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-08 conn-port=1 priority=1 type=staticNRL failed

24 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-09 conn-port=1 priority=1 type=staticNRL failed

25 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-10 conn-port=1 priority=1 type=staticNRL failed

26 AGENT PM ERROR- CLI command remove vlan all failed

27 AGENT PM ERROR- CLI command remove fwddb all failed

28 AGENT PM ERROR- CLI command add fwddb mac=01-00-00-00-00-10 conn-port=1 priority=1 type=staticNRL failed

config.err Message Responses

Some typical error log file messages and the recommended responses are provided below (without the

prefix of “

AGENT PM ERROR: CLI command”).

Message

set ip-mgmt state=enable failed

Response

: 1. Check if this is a recurring problem. 2. Verify the operation in the related section of this

manual. Retry the operation. 3. See the related DHCP command in “

Section 6: Command Line Interface

(CLI) Reference”.

4. If the problem persists, contact Technical Support.

Message

set dhcp state=disable failed

Response

: 1. Check if this is a recurring problem. 2. Verify the DHCP operation in the related section of

this manual. Retry the DHCP operation. 3. See the related DHCP command in “

Section 6: Command Line

Interface (CLI) Reference”.

4. If the problem persists, contact Technical Support.

Message

set ip type=ipv4 addr=192.168.0.10 subnet-mask=255.255.255.0 failed

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands