Lantronix x6010 User Manual Download Page 212

Page: 212 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 212 of 261

J8 – HW-SW Mode Jumper

Jumper J8 defines the x6010 Hardware / Software mode setting. Use the shorting plug to jumper (short):

•

Pins 1 and 2 for Hardware Mode. In this mode, the hardware defines the x6010 configuration.

•

Pins 2 and 3 for Software Mode. In this mode, the software defines the x6010 configuration (the

default setting).

The J8 factory default setting is Software mode (pins 2 and 3 jumpered) as shown above.

Note that in Hardware mode you cannot make x6010 configuration changes from the Web interface, as

the screen fields are all grayed out. You can enter CLI commands with the x6010 in Hardware mode.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands