Lantronix x6010 User Manual Download Page 122

Page: 122 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 122 of 261

Command

Reboot (Warm Start) the C6010

Syntax

reboot

Description

Performs a reboot (“cold start the system”) of the device in the command line prompt.

Warning:

Doing a reboot or restart of a NID or the IONMM may cause some configuration backup

files to be lost and the USB or Telnet session to drop. Doing a reboot, restart or upgrade of the IONMM,

a power restart of the chassis, or a reset to factory removes temporary files (e.g. configuration backup

files, Syslog file). A Factory Reset also removes the permanent settings (e.g. configuration files, HTTPS

certification file, SSH key).

Example 1 (C6010)

C1|S18|L1D>

reboot

Warning: this command will restart system, connection will be lost and please login

again!

Password:private

Hello, this is ION command line (version 1.00).

C1|S1|L1D>

The HyperTerminal connection closes and the Windows Taskbar Notification area displays the message

“

A network cable is unplugged!

. “

To recover: 1. Close the Windows Taskbar message. 2. Disconnect and close HyperTerminal. 3. Re-open

HyperTerminal. 4. Re-open the HT session. 5. Log back in to the x6010.

Example 2 (S6010)

C1|S4|L1AP2|L2P2>

reboot

Warning: this command will restart system, connection will be lost and please login again!

Warm start failed.

C1|S4|L1AP2|L2P2>

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands