Lantronix x6010 User Manual Download Page 247

Page: 247 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 247 of 261

Appendix B: Factory Defaults

The x6010 NID

Device

Level Factory Defaults are shown in the tables below.

Note

: The default settings

shown are as seen in the tabs/fields of the x6010 Web interface.

Device-Level Factory Defaults

Table 14: Device-Level Factory Defaults

Hardware Mode

System Level

ION / private

System Name

Device dependent (e.g., C6010-

3040)

Device Description

TDM mode

Depends on DIP switch position

DIP switch 4-4, UP: T1, Down:E1

In-band Loopback

Selection

Depends on DIP switch position

DIP switch 3-4, UP: Disabled,

Down: Enabled.

Start Pattern: “11000”

Stop Pattern: “11100”

Port-Level Factory Defaults

Table 15: Port-Level Factory Defaults

Port 1

Circuit ID

AIS Transmit

Depends on DIP switch position

DIP switch 4-1, UP: Disable,

Down: Enable

Transmit All Ones

Enabled

Long Haul

Depends on DIP switch position

Valid on T1 only

DIP switch 4-3, UP: No, Down: Yes

Line Build Out

Depends on TDM mode & DIP

switch position

See Table 17 below.

Loopback Type

Depends on front panel DIP

switch.

Switch 2, CL: PHY Layer,

Middle: No Loopback

Loopback Status

Depends on front panel DIP

switch.

Switch 2, CL: Local in Loopback,

Middle: No Loopback

Port 2

Circuit ID

AIS Transmit

Depends on DIP switch position

DIP switch 4-2, UP: Disable,

Down: Enable

Transmit All Ones

Enabled

Loopback Type

Depends on front panel DIP

switch.

Switch 2, FL: PHY Layer,

Middle: No Loopback

Loopback Status

Depends on front panel DIP

switch.

Switch 2, FL: Local in Loopback,

Middle: No Loopback

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands