Lantronix x6010 User Manual Download Page 99

Page: 99 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 99 of 261

16.

If upgrading more than one device, you may have to click

Refresh

again.

Note:

the upgrade will take one or more minutes to complete. The exact amount of time for the

upgrade depends on the number of modules being upgraded.
17.

After the upgrade has successfully completed, “

success

” displays in the

Status

column of the

Result sub-tab window. If the upgrade fails, the

Reason

column displays a failure code.

See “

Section 5 – Troubleshooting

” for error messages and recovery procedures.

Check the

MAIN

tab for each upgraded module to ensure that the correct revision level is

displayed in the

Software Revision

field. You may have to click

Refresh

to display the updated

Software Revision level.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands