Lantronix x6010 User Manual Download Page 106

Page: 106 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 106 of 261

Replacing a Chassis Resident NID

The x6010 is a “hot swappable” device (it can be removed and installed while the chassis is powered on).

To replace a chassis resident x6010, do the following.
1.

Backup the configuration (see

Backing Up Slide-In and Remote Modules

Disconnect any cables attached to the x6010.

Loosen the panel fastener by turning it counterclockwise.

Pull the x6010 from the Chassis.

Carefully slide the new x6010 fully into the slot until it seats into the backplane.

Push in and rotate the attached panel fastener screw clockwise to secure the x6010 to the chassis.

Connect the appropriate cables to the x6010.

Load (restore) the configuration into the new x6010 (see

Restoring Slide-In and Remote Modules).

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands