Lantronix x6010 User Manual Download Page 156

Page: 156 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 156 of 261

Cannot show circuit-ID on this card!

You tried to display the Circuit ID information, but the function is not supported.

Make sure this is the command / function that you wanted.

Use the

command to switch to a device that supports Circuit ID display.

Try entering the command again. See “

Circuit ID

”.

If the problem persists, contact Technical Support.

Cannot set circuit-ID on this card!

You tried to display the Circuit ID information, but the function is not supported.

Verify the Circuit ID parameters. See “

Circuit ID

”.

Try entering the command again.

If the problem persists, contact Technical Support.

Please reboot the card for the changes to take effect!

You made a change that requires a system reboot in order for the change to take effect. For example:

C1|S5|L1D>

set snmp traphost svr 1 type ipv4 addr 192.168.1.30

Please reboot the card for the changes to take effect!
C1|S5|L1D>

Reboot the card. See the “

Reboot

” section.

Continue the operation.

If a problem persists, contact Technical Support.

Get DMI identifier no such object.

You entered the CLI command to display DMI information, but it was not available. For example:

C1|S3|L1P2>

show dmi info

Get DMI identifier no such object.
C1|S3|L1P2>

Make sure this is the command / function that you wanted.

Try entering the command again. See “

DMI (Diagnostic Maintenance Interface) Parameters

”

If a problem persists, contact Technical Support.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands