Lantronix x6010 User Manual Download Page 35

Page: 35 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 35 of 261

Installing the USB Driver

IMPORTANT

The following driver installation instructions are for the

Windows XP

operating system only. Installing

the USB driver using another operating system is similar, but not necessarily identical to the following

procedure.

To install the USB driver on a computer running

Windows XP

, do the following.

Extract the driver from the

website

and place it in an accessible folder on the local drive of the PC.

Connect the NID to the USB port on the PC.

Note:

for slide-in modules installed in an ION Chassis, the USB connection will be made to the ION

Management Module if one is installed in the chassis.
The

Welcome to the Found New Hardware Wizard

window displays.

Select

No, not this time

Click

Next

. The installation options window displays.

Select

Install from a list or specific location (Advanced)

Click

Next

. The driver search installation options window displays.

Click

Browse

. Locate and select the USB driver downloaded in step 1 above.

Click

Next

. Driver installation begins.

When the finished installing screen displays, click

Finish

The USB driver installation is complete. You must now configure the COM port to be used by the

terminal emulator.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands