Lantronix x6010 User Manual Download Page 193

Page: 193 / 261

Lantronix

ION x6010 User Guide

33493 Rev. F

https://www.lantronix.com/

Page 193 of 261

Message

Are you sure to power reset this slot? (After power reset, it will take a while to see card change

in this slot; please fold/unfold the Chassis node in the left tree panel to check the progress. If the card

information changes on the Tree, then click the Refresh button on this page

Meaning

: A caution message generated at the

Chassis

MAIN

tab. You clicked the

Reset

button for a

particular slot.

Recovery

If you are not sure that you want to reset this slot, click the

Cancel

button to clear the message and

return to normal operations without resetting power to this slot.

If you are sure that you want to reset this chassis, click the

button to clear the message and reset

power to the slot.

At the

Chassis

MAIN

tab, fold/unfold the Chassis node in the tree panel to check the progress.

If the card information changes on the Tree, then click the

Refresh

button on this page.

See the “

Menu System Notes

” section.

If the problem persists, contact Technical Support.

Summary of Contents for x6010






































































































































































































































































Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands

Lantronix x6010, User Manual

Search results

Summary of Contents for x6010

Reviews:

Related manuals for x6010

Brands by name

Popular brands