968
YASKAWA
SIEPC71061737B GA800 Drive Technical Reference
■
n8-39: HFI LPF Cutoff Freq
No.
(Hex.)
Name
Description
Default
(Range)
n8-39
(0566)
PM Phase Compensation
Gain
Sets the low-pass filter shut-off frequency for high frequency injection.
250 Hz
(0 - 1000 Hz)
Note:
•
Set
n8-35 = 1 [Initial Pole Detection Method = High Frequency Injection]
or
n8-57 = 1 [HFI Overlap Selection = Enabled]
to enable this
parameter.
•
The drive automatically calculates this value when High Frequency Injection Auto-Tuning completes successfully.
■
n8-41: HFI P Gain
No.
(Hex.)
Name
Description
Default
(Range)
n8-41
(0568)
Expert
HFI P Gain
Sets the response gain for the high frequency injection speed estimation.
2.5
(-10.0 - +10.0)
Note:
•
Set
n8-35 = 1 [Initial Pole Detection Method = High Frequency Injection]
or
n8-57 = 1 [HFI Overlap Selection = Enabled]
to enable this
parameter.
•
Set
n8-41 > 0.0
for IPM motors.
Configure the setting as follows.
•
Decrease the setting in units of 0.5 if an oscillation or hunting occurs.
•
Increase the setting in units of 0.5 if tracking related to load changes is required.
■
n8-42: HFI I Time
No.
(Hex.)
Name
Description
Default
(Range)
n8-42
(0569)
Expert
HFI I Time
Sets the integral time constant for the high frequency injection speed estimation. Usually it is not
necessary to change this setting.
0.10 s
(0.00 - 9.99 s)
Note:
Set
n8-35 = 1 [Initial Pole Detection Method = High Frequency Injection]
or
n8-57 = 1 [HFI Overlap Selection = Enabled]
to enable this
parameter.
■
n8-45: Speed Feedback Detection Gain
No.
(Hex.)
Name
Description
Default
(Range)
n8-45
(0538)
Speed Feedback Detection
Gain
Sets the internal speed feedback detection reduction unit gain as a magnification value. Usually it is
not necessary to change this setting.
0.80
(0.00 - 10.00)
Adjust this parameter in these conditions:
•
If vibration or hunting occur, increase the setting value in 0.05 unit increments.
•
If the responsiveness of torque and speed is unsatisfactory, decrease the setting value 0.05 unit increments and
examine the response.
■
n8-46: PM Phase Compensation Gain
No.
(Hex.)
Name
Description
Default
(Range)
n8-46
(0539)
Expert
PM Phase Compensation
Gain
Sets the gain to compensate for phase differences. Usually it is not necessary to change this setting.
0.3
(0.0 - 10.0)
If there is vibration in the motor, increase the value. When you must detect
oC [Overcurrent]
or
ov [DC Bus
Overvoltage]
, set this parameter to a low value.
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
Содержание GA800 Series
