YASKAWA GA800 Series, Техническое описание

Страница: 965 / 1016

Parameter
Details
12
12.10 n: Special Adjustment
YASKAWA SIEPC71061737B GA800 Drive Technical Reference 965
■
n8-02: Pole Alignment Current Level
No.
(Hex.)
Name Description
Default
(Range)
n8-02
(0541)
Expert
Pole Alignment Current
Level
Sets the current at the time of polar attraction as a percentage of E5-03 [Motor Rated Current (FLA)] .
Usually it is not necessary to change this setting.
80%
(0 - 150%)
The drive uses the polar pull-in current to attract the rotor after it detects the initial rotor position. When you increase
the value of
n8-02 , the starting torque also increases.
•
If the motor does not track correctly at the time of the polar attraction, increase the value in 10% increments. If you
set the value too high, the drive will detect
oL2 [Drive Overloaded] .
• If the motor oscillates at the time of the polar attraction, decrease the value in 10% increments.
Note:
•
This function is available when you set A1-02 = 7 [Control Method Selection = CLV/PM] and do Rotational Auto-Tuning or Z Pulse Offset
Tuning.
• When A1-02 = 7 , this parameter takes effect only in Expert Mode.
■
n8-03: Pole Position Detection Time
No.
(Hex.)
Name Description
Default
(Range)
n8-03
(0542)
Pole Position Detection
Time
Sets the length of the Current Starting Time, which is used for Z Pulse Offset Tuning. Usually it is
not necessary to change this setting.
1.5 s
(1.5 - 5.0 s)
Sets the length of time of pull-in current when the drive detects the motor magnetic pole of the rotors.
Note:
If the motor oscillates at the time of the polar attraction, increase the value in 0.5 s increments. If the value is too high, the drive can detect
oL2 [Drive Overloaded] .
■
n8-04: Pole Alignment Time
No.
(Hex.)
Name Description
Default
(Range)
n8-04
(0543)
Expert
Pole Alignment Time
Sets the length of the Polar Attraction Time, which is used for Z Pulse Offset Tuning. Usually it is
not necessary to change this setting.
1.5 s
(1.5 - 5.0 s)
Sets the length of time that the pull-in current flows when the drive detects the motor magnetic pole of the rotors.
Note:
If the motor oscillates at the time of the polar attraction, increase the value in 0.5 s increments. If you set the value too high, the drive will
detect
oL2 [Drive Overloaded] .
■
n8-11: Observer Calculation Gain 2
No.
(Hex.)
Name Description
Default
(Range)
n8-11
(054A)
Observer Calculation Gain 2
Sets the gain for speed estimation. Usually it is not necessary to change this setting.
Determined by n8-72
(0.0 - 1000.0)
Note:
When n8-72 = 0 [Speed Estimation Method Select = Method 1] , the default value is 50.0. When n8-72 = 1 [Method 2] , the default value is
150.0.
■
n8-14: Polarity Compensation Gain 3
No.
(Hex.)
Name Description
Default
(Range)
n8-14
(054D)
Expert
Polarity Compensation Gain
3
Sets the gain for speed estimation. Usually it is not necessary to change this setting.
1.000
(0.000 - 10.000)
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f
CL-V/f
OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV