YASKAWA
SIEPC71061737B GA800 Drive Technical Reference
971
3 : Beyond 1:50
Adjust in the following situations.
•
The ratio between the motor inertia and machine inertia is more than 1:50
•
Parameter
n8-55 = 2
and the drive detects
STPo
because of an impact load or sudden acceleration/deceleration.
■
n8-56: PM High Performance Selection
No.
(Hex.)
Name
Description
Default
(Range)
n8-56
(056F)
Expert
PM High Performance
Selection
Usually it is not necessary to change this setting. Sets the high efficiency control method for IPM
motor.
1
(0 - 2)
0 : Disabled
1 : Enabled (Vd)
2 : Enabled (Vd & Vq)
■
n8-57: HFI Overlap Selection
No.
(Hex.)
Name
Description
Default
(Range)
n8-57
(0574)
HFI Overlap Selection
Sets the function that detects motor speed with high frequency injection.
0
(0, 1)
Note:
•
When you set
n8-57 = 1
, doHigh Frequency Injection Auto-Tuning.
•
When there is high frequency injection, the motor will make an excitation sound.
•
When you use Zero Speed Control, set
E1-09 [Minimum Output Frequency] = 0.0
.
0 : Disabled
Use this setting with SPM motors. The speed control range is approximately 1:20.
When
n8-57 = 0
, you cannot set
E1-09 [Minimum Output Frequency]
≤ 1/20 of the value of
E1-06 [Base Frequency]
.
1 : Enabled
The speed control range changes to 1:100 to give sufficient speed detection at low speeds.
Note:
It is not available with an SPM motor.
■
n8-62: Output Voltage Limit Level
No.
(Hex.)
Name
Description
Default
(Range)
n8-62
(057D)
Expert
Output Voltage Limit Level
Sets the output voltage limit to prevent saturation of the output voltage. Usually it is not necessary to
change this parameter.
200 V Class: 200.0 V, 400 V
Class: 400.0 V
(200 V Class: 0.0 to 240.0 V,
400 V Class: 0.0 to 480.0 V)
Set this parameter lower than the input power supply voltage.
Note:
•
When
A1-02 = 7, 8 [Control Method Selection = CLV/PM, EZOLV]
, this parameter is available in Expert Mode.
•
When
A1-02 = 8
, the default setting is
–
200 V Class: 230.0 V
–
400 V Class: 460.0 V
■
n8-63: Output Voltage Limit P Gain
No.
(Hex.)
Name
Description
Default
(Range)
n8-63
(057E)
Expert
Output Voltage Limit P Gain
Sets the proportional gain for output voltage control. Usually it is not necessary to change this
setting.
1.00
(0.00 - 100.00)
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
V/f
CL-V/f
OLV
CLV
AOLV
OLV/PM
OLV/PM AOLV/PM CLV/PM
EZOLV
Содержание GA800 Series
