YASKAWA GA800 Series, Техническое описание

Страница: 515 / 1016

Parameter
List
11
11.9 F: Options
YASKAWA SIEPC71061737B GA800 Drive Technical Reference 515
No.
(Hex.)
Name Description
Default
(Range)
Ref.
F1-37
(03BD)
Encoder 2 Signal
Selection
Sets the number of channels for the signal to the encoder option card for motor 2.
0 : A Pulse Detection
1 : AB Pulse Detection
0
(0, 1)
787
F1-46
(1B98)
Deviation 2 Detection
Method Selection
Usually it is not necessary to change this setting. Sets the detection method for
dv2 [Z
Pulse Noise Fault Detection] .
0
(0, 1)
787
F1-47
(1B99)
Deviation 2 Detection
Selection
Usually it is not necessary to change this setting. Sets the sensitivity of detection for dv2 [Z
Pulse Noise Fault Detection] . Increase the value to decrease the sensitivity.
15°
(0 - 180°)
787
F1-50
(03D2)
PG-F3 Option Encoder
Type
Sets the type of encoder connected to the PG-F3 option.
0 : EnDat Sin/Cos
1 : EnDat Serial Only
2 : HIPERFACE
0
(0 - 2)
787
F1-51
(03D3)
PG-F3 PGoH Detection
Level
The drive will detect
PGoH [Encoder (PG) Hardware Fault]
if the value of this parameter
is smaller than the value of .
Note:
This function is enabled when F1-20 = 1 [Encoder 1 PCB Disconnect Detect =
Enabled] .
80%
(1 - 100%)
787
F1-52
(03D4)
Serial Encoder Comm
Speed
Sets the communication speed between the PG-F3 option and the serial encoder.
0 : 1M/9600bps
1 : 500k/19200bps
2 : 1M/38400bps
0
(0 - 2)
788
◆
F2: Analog Input Option
No.
(Hex.)
Name Description
Default
(Range)
Ref.
F2-01
(038F)
Analog Input Function
Selection
Sets the input method for the analog reference used with AI-A3.
0 : 3 Independent Channels
1 : 3 Channels Added Together
0
(0, 1)
788
F2-02
(0368)
RUN
Analog Input Option Card
Gain
Sets the analog reference gain as a percentage when the maximum output frequency is
100%.
Note:
•
Set F2-01 = 1 [Analog Input Function Selection = 3 Channels Added Together] to
enable this function.
• Parameter A1-02 [Control Method Selection] selects which parameter is the
maximum output frequency.
– A1-02 ≠ 8 [EZOLV] : E1-04 [Maximum Output Frequency]
– A1-02 = 8 : E9-02 [Maximum Speed]
100.0%
(-999.9 - +999.9%)
790
F2-03
(0369)
RUN
Analog Input Option Card
Bias
Sets the analog reference bias as a percentage when the maximum output frequency is
100%.
Note:
•
Set F2-01 = 1 [Analog Input Function Selection = 3 Channels Added Together] to
enable this function.
• Parameter A1-02 [Control Method Selection] selects which parameter is the
maximum output frequency.
– A1-02 ≠ 8 [EZOLV] : E1-04 [Maximum Output Frequency]
– A1-02 = 8 : E9-02 [Maximum Speed]
0.0%
(-999.9 - +999.9%)
790
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV