YASKAWA GA800 Series, Техническое описание

Страница: 499 / 1016

Parameter
List
11
11.6 C: Tuning
YASKAWA SIEPC71061737B GA800 Drive Technical Reference 499
No.
(Hex.)
Name Description
Default
(Range)
Ref.
C3-24
(0243)
Motor 2 Slip Comp
during Regen
Sets the slip compensation during regenerative operation function for motor 2.
0 : Disabled
1 : Enabled Above 6Hz
2 : Enabled Above C3-15
0
(0 - 2)
721
C3-28
(1B5B)
Expert
Adaptive Slip Control
Mode
Sets the slip compensation function mode.
0 : Normal
1 : Advanced
0
(0, 1)
721
◆
C4: Torque Compensation
No.
(Hex.)
Name Description
Default
(Range)
Ref.
C4-01
(0215)
RUN
Torque Compensation
Gain
Sets the gain for the torque compensation function. Use this parameter value for motor 1
when operating multiple motors.
Note:
If A1-02 = 8 [Control Method Selection = EZOLV] , you cannot change the setting
while the drive is running.
Determined by A1-02
(0.00 - 2.50)
722
C4-02
(0216)
RUN
Torque Compensation
Delay Time
Sets the torque compensation delay time. Usually it is not necessary to change this setting.
Note:
If A1-02 = 8 [Control Method Selection = EZOLV] , you cannot change the setting
while the drive is running.
Determined by A1-02
(0 - 60000 ms)
722
C4-03
(0217)
Torque Compensation @
FWD Start
Set the amount of torque reference for forward start as a percentage of the motor rated
torque.
0.0%
(0.0 - 200.0%)
722
C4-04
(0218)
Torque Compensation @
REV Start
Sets the amount of torque reference for reverse start as a percentage of the motor rated
torque.
0.0%
(-200.0 - 0.0%)
723
C4-05
(0219)
Torque Compensation
Time
Sets the starting torque constant to use with C4-03 and C4-04 [Torque Compensation @
FWD/REV Start] .
10 ms
(0 - 200 ms)
723
C4-06
(021A)
Motor 2 Torque Comp
Delay Time
Sets the value if ov [Overvoltage] occurs with sudden changes in the load, at the end of
acceleration, or at the start of deceleration.
150 ms
(0 - 10000 ms)
723
C4-07
(0341)
RUN
Motor 2 Torque
Compensation Gain
Sets the gain for motor 2 torque compensation function when using the Motor Switch
function.
1.00
(0.00 - 2.50)
723
C4-19
(0B8D)
RUN
Expert
Torque Ripple Suppress
Min Freq
Adjust this if slow oscillation occurs at low speeds. Increase this parameter in 1.0 Hz
increments when current ripples and torque ripples occur during low-speed operation. Set
this parameter to 0.0 to disable the function if increasing the value does not fix the
problem. Usually it is not necessary to change this setting.
0.1 Hz
(0.0 - 10.0 Hz)
723
C4-20
(0BCB)
Expert
Voltage Compensation
Adjust 1
Sets voltage precision compensation. Usually it is not necessary to change this setting.
120
(0 - 200)
724
C4-21
(0BCC)
RUN
Expert
Voltage Compensation
Adjust 2
Sets voltage precision compensation. Usually it is not necessary to change this setting.
5
(0 - 10)
724
C4-23
(1583)
RUN
Expert
Current Control Gain
Current control gain. Usually it is not necessary to change this parameter.
1.00
(0.50 - 2.50)
724
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV